Repair Car Dent with Hammer and Pliers Method

It can be frustrating when you have a dent in your car. You might not know where to go for the repair or what tools are needed. This blog post has tips on how to repair car dent, so it looks as good as new again. 

This blog post will give you the information and steps on repairing dents in cars, from identifying which type of damage it is. Determining if there’s another underlying problem, assessing the extent of the damage, and finally, how to fix it! 

We’ll also cover various tools that will come in handy when repairing an car dent. Including hammers, body filler, metal polish, and more. If you would like to learn more about this topic of improvement, keep reading.

Get the Right Supplies

Before you begin to repair a car dent, you will need to get the right supplies.

You may be able to find what you need around your home for this project. However, if not, it might be an inexpensive trip to make some necessary purchases.

These are the supplies you will need:

  1. Pliers 
  2. Hammer
  3. Paint
  4. Glue
  5. Sandpaper

Also read: How to Make the Car Interior Look New – Ultimate Guide

Find Out What Caused the Dent

It would help if you determined why your vehicle has a dented. If you do not, it could lead to further issues when trying to fix the problem.

After you find out how the dent got there, try pulling or pushing on it in different ways to see how it pops out. This will help when fixing the damage.

Clean around the Damaged Area

Ensure to clean the area where you found the dent to prevent future damage while you are trying to fix it.

Use an air compressor or something similar to blow off any dirt or debris that may be on the surface of your car.

After that, use a wet cloth to wipe around the area to get off wax and other things that may be protecting your car’s paint job.

Now you’re ready to go on repairing the dent in your car.

Hammer and Pliers Method    

Get behind where you think the dent is located.

Use your hands to push the area out of the way, which will make the dent pop up.

Hammer down on the center of it until it pops back inside. It’s important that you don’t hammer too hard, or else you could end up with an indentation of where you were trying to fix it.

The plier’s method is similar but instead uses pliers to flatten out car dents by applying pressure on each side of them until they pop back into place. Lift the dented section of your car evenly and slowly so that no new damage is created.

Paintless Dent Removal  

This process uses a special PDR tool, which is used to remove minor dents without painting the surface and easily repair car dent.

The special tool works by applying stress to the metal until it returns round or straight. Then you spray on some glue or putty and push it into any gaps that might appear before pushing down again. This will come out looking like new once you’re done with this process, which is why it’s called paintless dent removal.

You will need to make sure that your car is not very old. If you want to try this method because they can be expensive and may not even work after a certain age. Since most cars are made of plastic now instead of metal.

Sand Down all of your Repairs

Closely inspect your repairs and look for any pockmarks or areas that you could not properly smooth out. Take a sanding sponge made of high-grit paper and use it to rid your car’s surface of any dents. Including that leftover from the process.

Wear safety glasses to prevent any flying particles from hitting your eyes while sanding. You also want to make sure that you are wearing gloves because the paper can be sharp and damage your hands.

After they have been sanded down, wipe them off with a piece of cloth to get rid of any residue or dust on them so that your repairs will show up like new.

Fill in all of those Little Holes with Putty

Apply putty or glue to where the dent was once located. Sometimes, you might need to reinforce your repair job for it to last longer than just a little bit of time. That is why you should use some putty or adhesive over the top of them after they have been finished being sanded down.

It’s recommended that you get a professional to do this part of the process. If you have no experience using putty or glues on your car, which can be dangerous and extremely expensive if not done correctly.


How long do dents last?

Most dents go away over time, but if you are not patient enough to wait for them to go away on their own. You can hire a professional who knows how to perform the appropriate car dent repair service needed.

What is better than paintless dent removal or regular dent repair?

It’s determined by your situation and the needs of your car. It would help if you made sure that the paintless dent removal is right for you. Or else it may end up with your car looking worse than when it started.

What can PDR tools do?

Paintless dent removal or paint-free dent repair, short for PDR, is a non-destructive form of bodywork used to remove dents from a wide range of materials, including metal, plastic, and glass.

What does the PDR tool use?

The tools used for paintless dent repair are either manually powered or air-powered. Manual tools include bump hammers, body hammers, and dollies, while air tools include grinders, pin-pullers, and pick slides.

Why should I use this method when it’s so much more expensive than regular dent removal?

You want to use paintless dent repair because the results are usually longer lasting than. If you were to take your car in for traditional method of repair car dent.

Sharing Is Caring:

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.